Hobart AM16 dishwasher Error Codes
Applies to: AM16 door-type dish machines. Compiled and paraphrased from Hobart's own AM16 Series Dishwashers customer support manual, FORM 41339 (April 2025), published by Hobart and distributed through its dealers, covering the AM16-BAS, AM16T-BAS, AM16VL-BAS, AM16VLT-BAS, AM16-ASR, AM16T-ASR, AM16VL-ADV, AM16VLT-ADV, AM16SVL, AM16SVLT, AM16SCB, AM16TSCB, AM16VLSCB and AM16VLTSCB. The manual supplies every message text, the trigger values (temperatures, voltages, times), the operator action and the reset method given below, and the delime defaults. SCB models are the low-temperature chemical sanitizing versions, and some codes apply to them only. Message wording can change with software versions; confirm against the manual for your exact model. Table last updated Nov 6, 2026.
Not your model? Other Hobart code tables: LXi/AM15 door dish machines, CLeN rack conveyor dish machines.
Machine down now? 25 companies in this directory name Hobart on their own site, with who has been phone-confirmed and who covers nights. Or find a dish machine technician by city.
How to read the codes
The AM16 shows a THREE-DIGIT error number with a full sentence on its touch screen, and the sentence usually tells you what to do: Drain Machine, Call Service, or Close door. What the sentence does not tell you is how the machine is treating the fault, and Hobart's manual sorts them into four behaviours worth recognising. Some only need ACKNOWLEDGING with the Enter button and the cycle carries on (a slow booster, a fill that took too long). Some LOCK the wash program with a red blinking light and clear only by HOLDING THE POWER BUTTON FOR 5 SECONDS, after which the machine drains and switches off and you start again. Some are true error states with a solid red light where the machine will not run until the cause is fixed. And a few clear themselves once you fix the obvious thing: close the door, lock the strainer in place, refill the chemical. Several of the most common messages are about chemicals and strainers rather than faults, and they are yours to fix. The AM16 has no error history log in its manual; the Hobart SmartConnect app shows only the error that is active now, so write the number down before it is cleared. Older Hobart door machines such as the AM15 use a different, letter-based code set, covered in a separate table on this site.
The codes
| Code | Meaning | Likely causes | Operator-safe steps | Technician work |
|---|---|---|---|---|
| 001 / 002 | Booster thermistor error: Drain Machine, Call Service | The booster temperature sensor reads 239F or higher or is shorted (001), or reads 32F or lower or is open (002). A reading that extreme is a failed sensor or its wiring, not a real temperature | Drain the machine and call service. Enter will acknowledge it only once the reading is back between those limits | Booster thermistor and wiring |
| 003 / 004 | Booster temperature not reached during the FILL (003) or WASH (004) cycle | The booster did not reach its set point in the time allowed | Acknowledge with Enter; the cycle continues. Repeated occurrences mean rinse water may not be hot enough to sanitise, so book service rather than living with it | Booster heater, contactor, incoming water temperature |
| 006 / 007 | Sump thermistor error: Drain Machine, Call Service | The wash tank temperature sensor reads 239F or higher or is shorted (006), or 32F or lower or is open (007) | Drain the machine and call service | Wash tank thermistor and wiring |
| 008 | Wash tank temperature not reached during the fill cycle | The wash tank did not reach set point while filling. Hobart's response is firmer than for the booster: the FILL IS ABORTED and the machine goes to standby | Acknowledge with Enter. Check the incoming water is hot enough before calling | Tank heater, contactor, high limits, incoming water temperature |
| 014 / 015 | Booster pressure error: Drain Machine, Call Service | The booster pressure sensor signal is out of range high (014, 4.5V or more) or low (015, 0.30V or less): a sensor or wiring fault | Drain the machine and call service | Booster pressure sensor and connections |
| 016 / 017 | Wash tank pressure error: Drain Machine, Call Service | The wash tank pressure sensor, which the machine uses to judge water level, is out of range high (016) or low (017) | Drain the machine and call service | Wash tank pressure sensor and connections |
| 018 | Wash tank water level too high. Machine draining | Too much water in the wash tank. The machine drains itself | Wait for it to drain. When the Enter button appears press it; the machine powers off, and you press power to resume | If it recurs, fill valve or level sensing |
| 020 | Rinse system error: Check and Clean Rinse Arms | The water level did not rise enough during fill with the rinse pump running, which usually means the rinse arms are blocked | Press Enter to start a drain, then remove and clean the rinse arms. This is an operator fix | Rinse pump if clean arms do not cure it |
| 021 | Drain hose is clogged: clean drain hose and drain machine again | The drain hose or strainer is blocked | Clean the drain hose and check it for kinks. When the water has drained the Enter button appears; if the error stays, hold power for 5 seconds | Drain path and pump if cleaning does not clear it |
| 022 | Drain system error during wash program | Water did not drain within 5 MINUTES during a wash | Acknowledge with Enter. Check the drain hose, the strainer and that nothing is blocking the drain | Drain pump |
| 023 | Rapid fill timeout: inspect incoming water line (rapid fill kit units) | The water level did not rise in time on a machine fitted with the rapid fill kit | Check the water supply is on and the hose is not kinked; Hobart specifies 15 to 65 PSI. Press Enter, power off, then power on and refill | Supply pressure and fill valve |
| 029 / 039 | Door opened: Program interrupted (029) or Fill cycle interrupted (039). Close door | The door was opened during a program or during fill. 039 can also be a door switch fault if the door was not actually opened | Close the door; the message clears | Door switch, if it appears with the door shut |
| 032 | Fill error: inspect incoming water line | The booster level did not rise in time | Acknowledge with Enter. Check the water supply is on, pressure is within 15 to 65 PSI, and hoses are not kinked | Fill valve and supply pressure |
| 033 | Booster fill error: check incoming water line and shut-off valve | The booster did not reach its set point within 420 SECONDS | Acknowledge with Enter. Check the water supply, hoses and the shut-off valve is fully open | Booster fill path and heater |
| 035 | Ensure tank strainer is locked in place | The strainer is not detected. There is no Enter button: the message clears by itself when the strainer is sensed. A manager can enable or disable this check in the Manager Menu | Lock the tank strainer in place. This is the single most common message that is not a fault | None, unless a correctly fitted strainer is not detected |
| 038 | Incoming power too high: machine has powered down | Supply voltage above 280V | Turn off the circuit breaker and have the supply checked against the machine's data plate. That is an electrician's job | Measure supply voltage |
| 049 | Communication between the controls has been interrupted | The display and the control board have lost contact. The error does not clear until the fault is fixed | Call service | Cables and connectors between display and control board |
| 052 | Drain system error: check drain pump and hose | The water level stayed too high through 120 SECONDS of draining | Check the drain hose is not kinked or blocked. Enter acknowledges once the level has dropped | Drain pump, hose and anti-siphon |
| 054 | ASR strainer basket not detected (ASR models) | The ASR strainer basket is missing from the ASR box | Put the ASR basket in place. Pressing Enter lets cycles continue without ASR | None if the basket is fitted |
| 057 | Wash tank is filling: cycle will begin when water is replenished | The wash tank level dropped too low and the machine is topping up. A status message rather than a fault | Wait; the machine refills and resumes on its own | If constant, look for a leak or a drain valve not sealing |
| 075 | Rinse aid empty: refill rinse aid | Rinse aid not sensed | Refill the rinse aid; Enter reprimes the pump. If it persists with a full bottle, check the bottle, tubing and clamps | Rinse aid pump and sensing |
| 077 | Detergent empty: MACHINE LOCKED | Detergent not sensed for 3 cycles. The machine stays locked until detergent is replaced | Replace the detergent; Enter reprimes the pump | Detergent pump and sensing if it locks with a full container |
| 079 | Sanitizer empty: MACHINE LOCKED (SCB models) | Sanitizer not sensed for 3 cycles on a chemical sanitizing machine. The lock is deliberate: without sanitizer the dishes are not being sanitised | Replace the sanitizer; Enter reprimes the pump | Sanitizer pump and sensing |
| 081 / 082 | Final rinse thermistor error | The final rinse sensor reads 239F or higher or is shorted (081), or 32F or lower or is open (082) | Call service. Enter acknowledges once the reading is back in range | Final rinse thermistor and wiring |
| 084 | Minimum final rinse temperature not reached: MACHINE LOCKED (SCB models) | On SCB models the final rinse did not reach 120F within 3 cycles | Hobart's clear for this one is to HOLD THE POWER BUTTON FOR 5 SECONDS: the machine drains and powers off, then power on and try again. Check the incoming hot water temperature | Incoming water temperature, heating |
| 085 | Wash tank overtemp tripped | The wash tank high limit has opened. A true error state with a SOLID RED light: the machine will not run | Call service. Enter clears it only after the fault is corrected | Tank heater, contactor, high limit, set points, thermal paste between thermistor and tank |
| 086 | Booster overtemp tripped | The booster high limit has opened. Solid red light; the machine will not run | Call service. Enter clears it only after the fault is corrected | Booster heater, contactor, high limit, set points, thermal paste |
| 087 | Minimum final rinse temperature not reached after repeating cycle | The final rinse did not reach 180F after repeated cycles. The wash program is locked (red blinking light) because rinse water below 180F does not sanitise on a high-temperature machine | Hobart's clear for this one is to HOLD THE POWER BUTTON FOR 5 SECONDS: the machine drains and powers off, then power on and try again. If it returns, call service | Booster heater amps per leg, thermistors, high limit, contactor, incoming water temperature |
| 088 / 089 | Wash tank (088) or booster (089) CONTACTOR FAULT: Pull Circuit Breaker(s) and Contact Service | A heater contactor is STUCK CLOSED, heating when no heat was asked for. The machine protects itself by adding water through the fill valve and running the drain pump if needed | Follow the message: TURN OFF THE CIRCUIT BREAKER(S) and call service. A heater that will not switch off is not something to keep resetting | Contactor CON2 (wash tank) or CON1 (booster) and their wiring, checked with the breaker off |
| 090 | Wash temperature not reached: drain and restart machine | The wash tank did not reach 153F within 20 MINUTES of Heating appearing on screen. Wash program locked, red blinking light | Hobart's clear for this one is to HOLD THE POWER BUTTON FOR 5 SECONDS: the machine drains and powers off, then power on and try again. If it comes back, call service | Wash thermistor, tank heater amps per leg, contactor, high limits, incoming water temperature |
| Delime required | Delime required. Start Delime Cycle? (prompt, not a fault) | A scheduled reminder. On non-ASR models it is based on cycle count, factory default 2000 CYCLES; on ASR, ADV and SVL models it is based on water hardness and usage, factory default 7 grains per gallon, which should be set to match your water | Select yes and press Enter. On non-ASR models, clean the strainer, insert the delime when prompted and close the door; the machine runs a 10 minute wash and 1 minute rinse, then drains and powers down. ASR models pump delime automatically, so keep the bottle stocked and the standpipe fully inserted | None. Set the hardness correctly on ASR models |
If this needs a dish machine technician
25 companies in this directory name Hobart on their own site: that page shows who has been phone-confirmed, who publishes 24/7 cover, and what each puts in writing. Start there if the brand matters more than the city.
Two questions worth reading before you ring anyone: what to do first when a code appears and how to tell whether it is yours to fix.
Or browse dish machines service companies by state:
Indiana: Evansville · Fort Wayne · Indianapolis · South Bend
Kentucky: Lexington · Louisville · Owensboro
Ohio: Akron · Cincinnati · Cleveland · Columbus · Dayton · Toledo · Upper Sandusky · Youngstown
Pennsylvania: Allentown · Altoona · Erie · Harrisburg · Lancaster · Pittsburgh · Scranton · Williamsport
West Virginia: Charleston · Clarksburg · Huntington · Martinsburg · Parkersburg · Wheeling
Related: the PM checklist that prevents the most common codes outright, and the operator guides for symptom-first diagnosis.
Not sure this is the right make? The lookup by code shows every make that uses a given code, and flags the ones that mean different things depending on the machine in front of you.